AEG Washing Machine Error Codes London – Complete Guide to Faults, Causes & Fixes

If your AEG washing machine has displayed an error code, and you live in London or the surrounding areas, don't worry. This comprehensive guide covers AEG washing machine error codes with detailed explanations, common causes, and step-by-step solutions. Whether you're looking to fix the problem yourself or need local technician support, this guide is here to help.

Why Does My AEG Washing Machine Display an Error?

Modern AEG washing machines are equipped with self-diagnosis systems that display an error code when certain issues arise, such as:

Water intake or drainage problems
Door lock not functioning properly
Issues with the motor or heating elements
Problems with power supply or electronics

Quick List of Error Codes

E10 / E11 / E12 – Water intake issues
E20 / E21 / E22 / E23 / E24 – Drainage problems
E30 / E31 / E32 / E35 / E38 – Pressure sensor faults
E40 / E41 / E42 / E43 / E44 / E45 – Door lock issues
E50 / E51 / E52 / E53 – Motor faults
E60 / E61 / E62 / E66 / E68 / E69 – Heating element problems
EF0 / EF1 / EF2 / EF3 / EF4 / EF5 – Excess foam or unbalanced load
EH0 / EH1 / EH2 / EH3 – Power supply issues
E90 / E91 / E92 / E93 / E94 / E95 / E96 – Internal electronics communication errors
EA0 / EA1 / EA2 – Drum position sensor errors

Detailed List of Error Codes, Causes & Solutions

E10 / E11 / E12: Water Intake Problems

Cause: These errors usually occur when the water intake is not functioning correctly.

Solution:

Check the water supply valve to ensure it’s fully open.
Inspect the inlet hose for any kinks or blockages.
Clean the water filter.
Ensure that the water pressure is sufficient.

E20 / E21 / E22 / E23 / E24: Drainage Problems

Cause: These errors typically indicate that the machine is unable to drain water properly.

Solution:

Clean the drain filter to remove any debris.
Check that the drain hose is not blocked or kinked.
Make sure the drainage pipe is clear and positioned correctly.
If the issue persists, the drain pump may need replacement.

E30 / E31 / E32 / E35 / E38: Pressure Sensor Faults

Cause: These errors point to problems with the pressure sensor or the water level in the drum.

Solution:

Check the pressure sensor and clean it.
Ensure there are no blockages in the hose connected to the pressure sensor.
If the issue continues, the pressure sensor may need to be replaced.

E40 / E41 / E42 / E43 / E44 / E45 — Door Lock Issues

Cause: These errors typically mean that the door lock is faulty or not engaging correctly.

Solution:

Ensure the door is properly closed, and the latch is engaged.
Check the door lock mechanism for wear and tear.
If the door lock mechanism is faulty, it may need replacement.

E50 / E51 / E52 / E53 — Motor Issues

Cause: These errors usually indicate that the motor is malfunctioning or there is a motor-related issue.

Solution:

Check the motor for obstructions or debris.
Make sure the motor's wiring is intact.
If the issue persists, the motor or motor control board may need to be replaced.

E60 / E61 / E62 / E66 / E68 / E69 — Heating Element Problems

Cause: These errors occur when the washing machine's heating element is faulty.

Solution:

Test the heating element with a multimeter to check for continuity.
If the heating element is damaged, replace it.
Check the temperature sensor for faults.

EF0 / EF1 / EF2 / EF3 / EF4 / EF5 — Excess Foam or Unbalanced Load

Cause: These errors often happen when there is too much detergent or the load is uneven.

Solution:

Reduce the amount of detergent used.
Ensure that the load is balanced inside the drum.
Run the machine on a gentle spin cycle to redistribute the load.

EH0 / EH1 / EH2 / EH3 — Power Supply Issues

Cause: These errors usually occur when there is a power supply issue, such as voltage fluctuations.

Solution:

Disconnect the machine from the power supply for a few minutes, then reconnect it.
Check for any voltage fluctuations in the electrical supply.
Use a surge protector to prevent damage from power spikes.

E90 / E91 / E92 / E93 / E94 / E95 / E96 — Internal Electronics Communication Errors

Cause: These errors indicate that there is a communication issue within the washing machine's control board.

Solution:

Power cycle the washing machine by unplugging it and plugging it back in after a few minutes.
If the issue persists, contact a professional technician for a control board replacement.

EA0 / EA1 / EA2: Drum Position Sensor Errors

Cause: These errors indicate that the drum position sensor is not detecting the drum's position correctly.

Solution:

Inspect the sensor for dirt or damage.
Clean the sensor or replace it if it is faulty.

Tips for Users in London

If you are based in London and your AEG washing machine displays an error code, you may want to consider calling a local engineer for a quick fix. Many appliance repair services in London offer same-day services or fixed-price repairs, which can be more convenient and cost-effective than trying to fix the issue yourself. Be sure to note down the error code and take a photo of the machine’s display before contacting a technician, as this will help them diagnose the issue faster.

Maintenance Tips to Avoid Common Errors

Clean the filter every 3 to 6 months.
Use the correct detergent for AEG machines and avoid overloading the drum with detergent.
Do not overload the washing machine, as this can strain the motor and cause error codes like E50/E51.
Leave the door slightly ajar after each use to prevent moisture buildup and avoid E13 errors.
If you live in an older building with lower water pressure in London, consider installing a water pressure booster.

Conclusion

Having a complete guide to all AEG washing machine error codes, along with causes and solutions, helps you troubleshoot problems quickly. Whether you're a DIY enthusiast or need professional assistance in London, this guide is designed to make your life easier. If you are unable to fix the issue yourself, don't hesitate to reach out to a local technician for expert help with AEG washing machine repair.