Blomberg Washing Machine Fault & Error Codes: Complete Guide for London Homes
Washing Machine Repair Services in London
When your Blomberg washing machine displays a fault code or an error code, it is the appliance’s way of telling you that something is not right. Whether you see E01, E04, CLon, or another code, this guide covers all known Blomberg washer fault codes and Blomberg washing machine error codes, explains what they mean, the possible causes, and how you or a repair engineer can fix them. This guide is especially useful for London households looking for clear and practical Blomberg appliance repair advice.
List of Blomberg Washing Machine Error & Fault Codes
E01 — Water Inlet Fault / Door Lock Error
Possible causes:
- The machine is not filling with water: the tap may be closed, the hose may be kinked, or the inlet valve may be blocked.
- The door may not be securely closed, or the latch or lock mechanism may be faulty, causing the machine to detect a fault.
How to fix / Solution:
- Make sure the water supply valve is open, the inlet hose is clear and not kinked, and clean the inlet filter.
- Check that the door closes fully, inspect the latch and lock, and replace the door lock mechanism if it is faulty.
E02 — Drain Error / Not Draining
Possible causes:
- The drain pump filter may be blocked by debris, preventing the pump from clearing water.
- The drain hose may be blocked, kinked, or incorrectly installed; the pump may also be faulty, or there may be a wiring issue.
How to fix / Solution:
- Clean the pump filter and remove any foreign objects.
- Check the drain hose for kinks or blockages, make sure it is installed correctly, and test or replace the drain pump if needed.
E03 — Heating Error / Water Not Heating
Possible causes:
- The heating element may be faulty or broken, or the thermostat / NTC sensor may be defective.
- The wiring between the heating element, thermostat, and control board may be damaged or loose.
How to fix / Solution:
- Test the heating element with a multimeter for continuity and replace it if it has failed.
- Check the thermostat / NTC sensor, inspect the wiring and connectors, and replace any faulty parts.
E04 — Motor Triac Shorted / Overfill Error, Depending on Model
Possible causes:
- There may be a short in the motor triac module or the control board driver circuit.
- On some models, this code means the machine has overfilled with water, often due to a faulty level sensor or an inlet valve stuck open.
How to fix / Solution:
- Inspect the motor connector block, wiring, and control board triac or driver module. Repair or replace faulty parts.
- If the machine has overfilled, check the inlet valve, pressure hose, and level sensor. Make sure the correct signal is reaching the control board and replace any defective part.
E05 — Temperature NTC Sensor Error
Possible causes:
- The NTC or temperature sensor may be defective, disconnected, or giving an incorrect reading.
How to fix / Solution:
- Check the sensor wiring and connections, and replace them if damaged.
- Test the sensor’s resistance according to the manual specification. If it fails the test, replace it.
E06 — Motor Tachometer / Motor Control Error
Possible causes:
- The motor tachometer, also known as the speed sensor, may be failing; carbon brushes may be worn on brush-type motors, or there may be a motor wiring fault.
How to fix / Solution:
- Inspect the motor speed sensor / tachometer wiring and connections, and test the motor brushes or motor if applicable.
- Replace the motor or related parts if a fault is confirmed.
E07 — Door Lock / Door Latch Error
Possible causes:
- The machine may not be detecting the door as closed; the latch mechanism may be faulty, or the wiring to the lock module may be loose.
How to fix / Solution:
- Check that the door closes fully and the latch engages properly. Inspect the door catch and lock wiring.
- Replace the latch or lock module if necessary.
E08 — Water Level Sensor / Pressure Sensor Error
Possible causes:
- The pressure hose from the drum to the sensor may be blocked or disconnected, or the level sensor may be faulty and giving the wrong reading.
How to fix / Solution:
- Inspect and clean the pressure hose. Make sure it is fitted correctly and is not kinked or blocked.
- Test or replace the level sensor if defective, and check the wiring to the sensor and control board.
E09 — Communication / Programme Selector / Control Board Fault
Possible causes:
- There may be faulty communication between the main control board and the sub-board or display.
- The programme selector, dial, or switch may be faulty.
How to fix / Solution:
- Unplug the machine for 5 minutes to attempt a reset, then check if the code returns.
- If the error continues, inspect the wiring between the selector / display and the control board, and replace the faulty board or selector if needed.
E10 — Overfill Detected / Internal System Fault
Possible causes:
- The machine may have detected too much water, usually due to a faulty inlet valve, level sensor, pressure sensor, or control board issue.
- Depending on the model, this may also indicate a general internal fault.
How to fix / Solution:
- Check the inlet valve, level / pressure sensor, and wiring, and replace any failing parts.
- If it is a general internal fault, a qualified engineer may need to run diagnostics and possibly replace the control board.
E11 — Water Heating Fault Detected
Possible causes:
- The heating element or thermostat may be faulty, or the control board may be failing to activate heating.
How to fix / Solution:
- Test and replace the heater or thermostat if needed, and check the wiring and connections.
E12 — Door Latch Fault Detected
Possible causes:
- The latch mechanism or wiring may be faulty, or the door may not be detected as securely closed.
How to fix / Solution:
- Check the door closure and latch mechanism, and replace the latch or wiring if required.
E13 — Spin Speed Error / Tachometer Error
Possible causes:
- The motor tachometer may be faulty, the drive belt may be worn or slipping on belt-driven models, or there may be a motor or control board issue.
How to fix / Solution:
- Inspect the tachometer sensor, motor brushes, belt, and motor condition. Replace the faulty part if a problem is found.
E14 — Various Internal System Faults, Model Dependent
Possible causes:
- This may indicate a general internal fault in the system, such as the control board or multiple subsystems, depending on the model variant.
How to fix / Solution:
- Reset the machine. If the error returns, full diagnostics and likely control board replacement may be required by an authorised engineer.
CLon — Child Lock Enabled
Possible causes:
- The child lock function has been activated, preventing the programme from starting or the machine from operating normally.
How to fix / Solution:
- Deactivate the child lock from the control panel. Check your user manual for the exact button sequence.
18 — Incorrect Mains Frequency or Voltage
Possible causes:
- The electrical supply voltage or frequency is outside the machine’s specification, such as low or high voltage, or an incorrect region setting.
How to fix / Solution:
- Check the mains supply voltage and frequency. Speak to an electrician if it is outside the correct range, and make sure the machine is connected to a suitable power supply.
How to Reset a Blomberg Washing Machine
For many Blomberg washer error codes or fault codes, a simple reset can clear temporary glitches. Follow these steps:
- Turn off the washing machine and unplug it from the power socket.
- Wait for about 60 seconds.
- Plug it back in and press the Start/Pause button for 5 seconds.
- Select a quick wash or short programme and check whether the error code still appears.
If the code reappears immediately, the fault is likely genuine and you should arrange professional service.
When Should You Call a Blomberg Repair Engineer in London?
If your machine is still under warranty, contact the authorised service centre. Otherwise, for any of the following issues with your Blomberg washing machine, you should consider professional repair:
- The error code continues after resetting.
- The fault involves the motor, heater, control board, or complex wiring.
- You are based in London and prefer expert same-day repair: Book Blomberg appliance repair in London.
Conclusion
Understanding the error codes and fault codes for your Blomberg washing machine helps you diagnose problems faster and decide when it is time for repair. Whether it is a simple blocked filter, a door latch issue, or a control board fault, acting quickly can reduce downtime and repair costs. If you are in London, our local Blomberg washer repair team is ready to help.
